Tel: +86-371-86151827

a709 gr 36 steel plate mill

Steel grade:a709 gr 36 steel plate mill

Thickness: 2mm-500mm

Certification: ABS, GL, BV, GOST, TS, CCS, CNNC, ISO

Payment Terms: T/T OR LC at sight

steel plate is widely used, involving various mechanical and engineering fields.

Tel: +86-371-86151827

E-mail: [sales1@bebonchina.com]

a709 gr 36 steel plate mill Introduction

A709 Structural, Carbon & HSLA Steel Plate - BBN Steel

BBN Steel stocks A709 Grade 36, A709 Grade 50 and A709 Grade 50W. These grades are often specified with Charpy tests referencing the specific zone or lowest anticipated service temperature. The Charpy tests are specified as non-fracture critical, which is a per-heat test (frequency "H"), or fracture critical, which is a per-plate test ...

ASTM A709 - SSAB high-strength steel - sheet, plate, coil ...

ASTM A709. The ASTM A709 is the Standard Specification for Structural Steel for Bridges and encompasses carbon, high-strength low-alloy, and quenched and tempered alloy steels used as structural plates in the construction of bridges. SSAB offers the following five grades of A709; 36, 50, 50W, HPS 50W and HPS 70W.

A709 Grade 36,A709Gr36,A709Gr36 PLATE - Mild steel plate ...

A709 grade 36 low alloy steel plate is mainly used for built steel bridges.HSLA steel plate A709Gr.36 owned minimum yield strength at 250Mpa and tensile strength between 400 and 550 Mpa.For the delivery condition of steel plate A709 Grade 36,As rolled,Control rolled,TMCP with or without accelerated cooling,or quenching and tempering is all ok.Xinsteel stock different thicknesses low alloy ...

A709 Gr.36 steel - steel-grades

Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. A709 Gr.36 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.

ASTM A709 Gr 36 low alloy steel plate ... - braunjp

ASTM A709 Steel Plate - Grade 36, 50, 50W | Leeco Steel, LLC. leecosteel› Steel Plate ProductsLeeco Steel offers ASTM A709 steel plate is primarily used in the manufacture of bridges.We offer A709 steel plate in the grades 36, 50 and 50W because they are grades are often specified with Charpy tests referencing the specific zone. ...[PDF]

Plate Specification Guide 2015-2016 - …

2015-2016 Plate Steel Specification Guide – Page 4 ASTM Specifications continued SPECIFICATION A204 Grade A A204 Grade B A204 Grade C A242†s Type 1** Type of Steel Alloy Alloy Alloy Carbon Requirements for Delivery A20 A20 A20 A6 Tensile Strength (ksi) 65/85 70/90 75/95 70 Min. to ¾" incl.; 67 Min. over ¾-1½" incl.;

Give You Our Best Carbon Steel Plate ASTM A709 Gr 100 ...

seekpart› …› Pipes & Fittings› Steel PipesSupply A709 Gr.36,A709 GR50,A709 Gr50S,A709 Gr. 100 carbon structural steel plate ASTM A709: Standard Specification for Structural Steel for Bridges 1. Steel Grade: A709 Grade 36, A709 … A 242 Type 1 steel plate,A 242 Type 1 steel supplier,A 242 ...

A709 Grade 50 mill - steel grade steel material

ASTM A709 Steel Plate - Grade 36, 50, 50W | Leeco Steel, LLC. ASTM A709 steel plate is primarily used in the manufacture of bridges. Leeco Steel stocks A709 steel plate Grade 36, 50 and 50W. These grades are often specified with charpy tests referencing the specific zone, or climatic region, in which the bridge will be in use.[PDF]

Steel grades according to American standards - A36, …

A709 - 04a Grade 36 0.26 0.05 0.04 ≤0.40 Grade 50 0.23 ≤1.35 0.05 0.04 ≤0.40 ... A709 - 04a Grade 36 ≥250 [36] 400-550 [58-80] 20 21 Grade 50 ≥345 [50] ≥450 [65] 18 21 ... Steel grades according to American standards - A36, A572, A588, A709, A913, A992.[PDF]

Plate - usa.arcelormittal

and Steel Institute (AISI), and the Depart-ment of the Navy. The efforts are coordinat-ed by the High Performance Steel Steering Committee. The first of these steels is ASTM A709 Grade HPS 70W (HPS 485W), known simply as HPS 70W. HPS 70W is defined as steel plate that has: • A minimum yield strength of 70 ksi (485 MPa)

ASTM A709 Plate - A709 Rolled Plate Supplier | Universal ...

universalsteelamerica› …› ASTM Structural PlatesUniversal Steel stocks A709 from 3/16” up to 4” thick. A709 is used in structural applications such as bridge building, for weight bearing and supportive components. Standard stock is provided in the as-rolled condition; however, normalized material can be obtained. A709 material with min Charpy (CVN) requirements is available upon request.

A 709 Gr. 50 W - BEBON steel - steel-plate-sheet

A 709 GR. 50 W steel plate is one mainly of Steel Resistant to Atmospherical Corrosion, A 709 GR. 50 W steel plate is a ASTM standard steel plate with different yield strength and tensile strength under different thickness. It is a kind of steel which is mainly used for steel resistant to atmospherical corrosion

A709 Grade 36 High Strength Low Alloy Steel Plate

A709 Structural, Carbon & HSLA Steel Plate - BBN Steel A high-strength, low-alloy structural steel plate utilized primarily in the manufacture of bridges. BBN Steel stocks A709 Grade 36, A709 Grade 50 and A709 Grade 50W.

a709 grade 50 plate| high strength steel plate-Triton ...

What is a709 grade 50 plate ? A709 is the specification used for steel plate used in the manufacture of bridges. Triton stocks A709 Grade 36, A709 Grade 50 and A709 Grade 50W. These grades are often specified with charpy tests referencing the specific zone (or …

ASTM A709 Gr 50W A588 Gr C Corten Steel Plate

A709 Structural, Carbon & HSLA Steel Plate - BBN SteelBBN Steel stocks A709 Grade 36, A709 Grade 50 and A709 Grade 50W. These grades are often specified with Charpy tests referencing the specific zone or lowest anticipated service temperature. The Charpy tests are specified as non-fracture critical, which is a per-heat test (frequency "H"), or fracture critical, which is a per-plate test ...

A709 Heavy Steel Plate - ASTM 709 Heavy Plate | Leeco ...

leecosteel› Steel Plate Products› Heavy Steel PlateASTM709 heavy steel plate is primarily used in the manufacture of bridges. Leeco Steel stocks A709 heavy steel plate Grade 36, 50 and 50W. These grades are often specified with Charpy tests referencing the specific zone, or climatic region, in which the bridge will be in use.

SA387 Gr12CL2 mill - MS Plates - napmr.org

high strength HP345 steel plates mill. grade GB6653 HP235 gas cylinder steel. hr I beam price per metric ton. grade P245NB steel plate specification. grade P265NB steel coil mill. high strength HP235 steel plate mill. factory 40L 50L 6M3 10m3 150BAR medical oxygen gas cylinder. China steel plate supplier A709 Gr 100 steel HR platesteel

A 709 Gr. 50 W - BEBON steel - steel-plate-sheet

A 709 GR. 50 W steel plate is one mainly of Steel Resistant to Atmospherical Corrosion, A 709 GR. 50 W steel plate is a ASTM standard steel plate with different yield strength and tensile strength under different thickness. It is a kind of steel which is mainly used for steel resistant to atmospherical corrosion

A709 Gr50|A709 Gr.50|A709-50 wind turbine steel plate- …

A709 Gr50|A709 Gr.50|A709-50 wind turbine steel plate . Steel Grade: ASTM A709 Grade 36,A709 Grade 50. Relative steel grades:A709 Gr.36,A709 Gr.50,A709 Gr.50W,A709 Gr.HPS 70W,S355N,S355NL,S420N,S420NL,S275N,S460N,S460NL,Q345E,Q345D. Main application:Mainly for wind turbine buildings,Winder tower buildings. Xinsteel Steel Wind Energy Group uses our entire company’s steel …

GUIDE TO SELECTION- PLATES | The Metal Store

GUIDE TO SELECTION- PLATES. 06-30-2011. LOW CARBON STEEL PLATE. ... MEDIUM CARBON STEEL PLATE. ... Most material is certified to ASTM A709 Gr. 36 bridge specification. ASTM A283 – GRADED – General purpose structural quality plate. Lower in cost and lower instrength compared with A36. Formable and weldable with proper care.

A709 Grade 50,A709Gr50,A709Gr50 PLATE - Mild steel plate ...

ASTM A709GR.50 steel plate is a kind of low alloy structural steel which is for building bridges in normal constructions.For a better weathering resistance,generally steel plate A709 Grade 50W is better used for outside situiations.When rolling these steel materials A709 Grade 50,for each reduction of 0.01% below the specified carbon maximum,an increase of 0.06 manganese above the specified ...

Astm A709 Steel Plate Wholesale, Steel Plate Suppliers ...

Alibaba offers 289 astm a709 steel plate products. About 95% of these are steel sheets, 4% are stainless steel sheets. A wide variety of astm a709 steel plate options are available to you, such as astm, aisi, and jis.

A709 Grade 50S density - MS Plates - napmr.org

A709 Grade 50S density, steel,Hot sell A709 Grade 50S density, MS Plates stock in China,China A709 Grade 50S density, MS Plates factory. Keeps more than 10,000 tons hot rolled and cold rolled A709 Grade 50S density, MS Plates in stock each month.

Steel Plate - EVRAZ North America

Steel plate is in railcars, barges, ocean-going vessels, industrial equipment, tanks and pressure vessels, large diameter pipe for oil and natural gas transmission, wind towers, bridges, armored vehicles and many other applications.

Farwest Steel Corporation

Farwest will coordinate priming ABS plate to your specifications prior to distribution or processing. Minimum yield for grade A over 1″ is 32 KSI. Maximum carbon content of 0.26 is acceptable for grade A equal to or less than 1/2″. Grade A plates over 1/2″ shall have a minimum manganese content of not less than 2.5 times the carbon content.

ASTM A709 Grade 50,A709 Gr.50 steel plate__Steel Supplier

Gangsteel is specialized in supplying ASTM A709 steel plate in A709 Grade 50. For more information of A709 Grade 50steel plates, please check them in following:. Chemical composition % of the Product analysis of A709 Grade 50

Steel grade

Steel specification

Our advantage

Steel Plate

1).2500mm production line-(Width:1600-2300mm, Thickness:6-30mm,Annual capacity:1,600,000 Tons;

The mainly steel plate we specialized in producing are shipbuilding steel, weathering resistant steel, boiler and pressure vessel steel, pipeline steel and so on. In addition, we can also arrange production according to the following standards - EN10025, EN10028, DIN 17100, ASTM A131, JISG3101, JISG3106...

2).3500mm production line-(Width:2000-3050mm, Thickness:10-80mm, Annual capacity: 2,000,000 Tons;

3).4300mm production line-(Width:1500-4100mm, Thickness:6-300mm, Annual capacity: 1,800,000 Tons;

Steel Pipe

The Seamless pipe production line range is OD 10.3mm--965.2mm, wall thickness 1.0mm--120mm, Annual capacity is 500 thousand tons.

We can do shot blasting and anti-corrosion according to DIN 30670 for diameter 10mm-3500mm,which is the most advanced level in China. To guarantee the quality, we can do Hydraulic test, Ultrasonic Testing, X-Ray test and drop hammer test before each shipment.

LSAW pipe production line range is OD 406mm--2500mm, wall thickness 6mm--50mm, Annual capacity is 150 thousand tons.

ERW pipe production line range is OD 17.1mm--660mm, wall thickness 0.6mm--22mm, Annual capacity is 100 thousand tons.

SSAW pipe production line range is OD 219.1mm--3500mm, wall thickness 3.2mm--25.4mm, Annual capacity is 200 thousand tons.

Stainless Steel

Cold rolled stainless steel plate/coil- (Thickness: 0.3-3.0mm; Width: 1000-2000mm; Length: According to customer's requirement; Surface:2B, 2D, BA, No.3, No.4)

Bebon has long term cooperation with TISCO, LISCO, ZPSS and Bao steel, etc..which are the top biggest and most famous stainless steel factories. Due to the good relationship with them, we have become their first-class agent. We can provide the best quality goods with competitive price.

Steel Plate & Coil Specification

Hot rolled stainless steel coil sheet
Cold rolled stainless steel coil & sheet
Thickness
3.0-12.0mm
Thickness
0.3-3.0 mm
Width
1219mm
Width
1000,1219,1500
Length
coil or as per requirement.
Length
coil or as per requirement.
Surface
No.1 or 1D
Surface
2B
Original
TISCO
Original
TISCO
Standard
GB/T4237-2015 ASTM A240/A240M JIS G4304
Standard
GB/T3280-2007 ASTM A240/A240M JIS G4305 EN10088-2:2005
MOQ for coil
13mt or as per coil actual weight
MOQ for coil
5mt or as per coil actual weight
MOQ for sheet
5 Pcs
MOQ for sheet
5 Pcs

According to the composition is divided into carbon steel and alloy steel, can be further classified according to uses, high strength low alloy steel plate, boilers and pressure vessels steel plate, mold plate, and shipbuilding and offshore platform steel plate, pipeline steel plate, wear-resistant steel plate, military uses steel plate and so on,

Boiler Or Pressure Vessel Steel Plate

It includes carbon steel, carbon manganese steel, micro-alloy steel, low alloy and high strength steel and low temperature steel. The working temperature is generally from -20C to 500C, and the individual can reach 560 degrees centigrade. The Pressure vessel steel plate is a special material related to the national economy and the people's livelihood. It is a short line product of the metallurgical industry.
Pressure Vessel Steel plate have many types, we can provide SA387, SA516, SA537, SA517 and so on, American Standard boiler or pressure vessel steel plate, already export to the United States, Australia, the Middle East, Southeast Asia and many other countries, high quality and low price, can be cut according to customer requirements..

Steel Standard:
ASTM A203 / ASME SA203, ASTM A204 / ASME SA204, ASTM A285 / ASME SA285
ASTM A299 / ASME SA299, ASTM A302 / ASME SA302, ASTM A387 / ASME SA387
ASTM A515 / ASME SA515, ASTM A516 / ASME SA516, ASTM A517 / ASME SA517
ASTM A533 / ASME SA533, ASTM A537 / ASME SA537, ASTM A612 / ASME SA612
ASTM A662 / ASME SA662
EN10028-2, EN10028-3, EN10028-5
DIN 17155

Carbon And Low-Alloy High-Strength Steel Plate

Carbon Steel, main point is that the mass fraction of carbon is less than 2.11% and does not contain the alloy elements and are specially added. Low-alloy high-strength steel is a kind of engineering structural steel developed by adding a small amount of Mn, Si and trace elements such as Nb, V, Ti and Al in the basis of Carbon structural steel.
The so-called low alloy is that the total alloy elements in the steel do not exceed 3%, which are mainly used for manufacturing various engineering structures with high strength, such as bridges, ships, vehicles, high pressure vessels, oil and gas transmission pipelines, large steel structures and so on.
Carbon steel plate and low alloy high strength steel plate, is the most common and widely used steel plate, strong supply capacity, the domestic production of the largest steel plate, we can cut processing according to customer requirements, and also can be processed according to the requirements of the drawings by grinder, our finished products are praised by our many customers, welcome to send us the enquiries and the drawing.

Steel Standard:
ASTM A36, ASTM A283, ASTM A514 / ASME SA514
ASTM A572 / ASME SA572, ASTM A633 / ASME SA633, ASTM A709
EN10025-2, EN10025-3, EN10025-4, EN10025-6 
DIN17100, DIN17102
GB/T700, GB/T1591, GB/T16270

Shipbuilding Or Offshore Structural Steel Plate

Marine steel plate refers to the hot rolled steel plate used to manufacture the hull structure according to the standard requirements of the Classification Society. Shipbuilding or Offshore structural steel plate, first, good toughness is the most critical requirement. In addition, it requires high strength, good corrosion resistance, welding performance, processing performance and surface quality. In order to ensure quality and ensure enough toughness, the chemical composition of Mn/C is above 2.5, and the carbon equivalent is also strictly required, and it is produced by a steel factory approved by the Ship Inspection Department. With the development of marine industry, the steel demand is rising dramatically, in addition to the ordinary ship plate, offshore platform steel plate in recent years is the demanded for a wide range. Our Steel's EN10225 standard steel plate, get the praise of our many customers, including S355G7, S355G8.

Ship Class Steel Plate

Standard: CCS, ABS, LR, GL, BV, DNV, KR, RINA, ETC

Grade :A, B, D, E, AH36, DH36, EH36, AH40, DH40, EH40, FH36, FH40

Thickness : 8mm-500mm 
Width : 1000mm-4000mm 
Length : 1000mm-20000mm


EN10225 Weldable Structural Steels for Fixed Offshore Structures.

Standard: EN10225
Grade :S355G2+N, S355G3+N, S355G5+M, S355G6+M, S355G7+N, S355G8+N, S355G7+M, S355G8+M, S355G9+N, S355G9+M, S355G10+N, S355G10+M
S460G1+QT, S460G1+M, S420G2+QT, S420G2+M,S460G3, S460G4,and so on.

Thickness : 8mm-500mm 
Width : 1000mm-4000mm 
Length : 1000mm-20000mm


API Spec 2H specification for Carbon Manganese Steel Plate for Offshore Structures, API Spec 2H specification covers two grades of intermediate strength steel plates up to 4 in. thick for use in welded construction of offshore structures

Standard: API SPEC 2H
Grade :API Spec 2H Grade 42, Grade 50

Thickness : 8mm-500mm 
Width : 1000mm-4000mm 
Length : 1000mm-20000mm

Wear Resistant Steel Plate

Wear resistant steel plate has high wear resistance and good impact resistance, capable of cutting, bending, welding, welding, can take the plug welding and bolt connecting with other structures are connected, the advantages of time saving, convenient in maintenance process, widely used in metallurgy, coal, cement, electricity, glass, mining, building materials, tiles and other industries, compared with other materials, has a very high price, has been more and more favored by the industry and manufacturers.

Standard: WEAR RESISTANCE STEEL PALTE
Grade :NM360, NM400, NM500, NM550

WNM360, WNM400, WNM450, WNM500

Thickness : 8mm-150mm 
Width : 1000mm-4000mm 
Length : 1000mm-20000mm


If you are interested in our company or products, welcome to visit our company or local offices; you can also get contact with us through online consulting, demand table submission, e-mails and telephones. Our staff shall wholeheartedly provide product information, application knowledge and good service for you.

Inquiry

Please send your processing requirement/ the drawings to sales1@bebonchina.com or leave a message below. Our professional after-sales personnel will response you in 24 hours.