Tel: +86-371-86151827

a36 steel sheet thicknesses

Steel grade:a36 steel sheet thicknesses

Thickness: 2mm-500mm

Certification: ABS, GL, BV, GOST, TS, CCS, CNNC, ISO

Payment Terms: T/T OR LC at sight

steel plate is widely used, involving various mechanical and engineering fields.

Tel: +86-371-86151827

E-mail: [sales1@bebonchina.com]

a36 steel sheet thicknesses Introduction

Plate A36 - Benjamin Steel

Thickness in Inches: Widths: Lengths: Lbs/Sft: 3/16: 48, 60, 72, 84, 96: 96, 120, 124,133, 144, 156, 240: 7.660: 1/4: 48, 60, 72, 84, 96: 96,110, 120, 144, 240: 10.210

Minimum Thickness for ASTM A36 Sheet... - Metal and ...

eng-tips› …› Metal and Metallurgy engineering ForumApr 23, 2003· I have a quick one, although not easy to find the answer documented anywhere. What is the minimum thickness one can order A36 Steel sheet? I am doing a calc and the designer specified 1/8" A36 sheet, but the customer is now saying that A36 does not come in a thickness less than 3/16".Apparently you don't have the ASTM A-36 standard handy. Well, neither do I until tomorrow. But that's where you'll find the answer.No, I do have the standard and it does not specify a minimum. What it does say is this. Under Table 2 Chemical Requirements, there are thicknesses designated according shape. For plates, the bottom range says: To 3/4" [20] incl. Basically, its saying up to 3/4" or 20 mm, but no bottom limit. I can only assume that 1/8" is included in the range, but that's an unverified assumption requiring verification at some point! thanksI think 1/8" is below the thickness of "plate" and falls into the "sheet" category. As such, A-36 may not apply, and if I were you I would look for a similar specification that covers "sheet".Well, A36 is a spec for Carbon Structural Steel, period. Now, we are considering substituting A570 grade 45 so that the mechanical properties are enveloped with our calc, but we want to make sure that we absolutely have to before we do that. Also, we want to make sure these guys are not telling us something that is, in fact, incorrect. Therefore, we just want to make sure so that we are covered. Its a CYA thing paralleled with the principle that A36 should be fine. Thanks again.cozdemir, As IFR stated, 1/8" thickness falls under the category of sheet/strip, and therefore ASTM A 570 should be referenced instead of ASTM A 36. ASTM A 570 is listed as an Appurtenant Material Specification in Table 1 of Section 4.I have the current copies of the ASTM A 6 and A 36 standards. Neither of these delineate the cut-off point for plate to sheet (or vice versa). As previously noted, plate is generally considered to be material >1/8" in thickness.Plate is classified as anything 3/16 and thicker. Sheet is 7 gage and thinner. A569 is the closest thing to A36 plate, both are bottom-of-the-barrel, merchant quality steel.

What is ASTM A36 steel and the steel sheet thickness and ...

The A36 standard was established by the standards organization ASTM International. ASTM A36 covers the chemical and mechanical requirements for carbon steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded construction of bridges, buildings, and general structural purposes. Bolts manufactured from A36 steel ...

A36,A36 STEEL,A36 PLATE - Mild steel plate,shipbuilding ...

ASTM A36/A36M A36 steel plate is a kind carbon structure steel which is used in riveted,bolted or welded construction of bridges and buildings,and for general structural purpose.The yield strength of carbon steel plate A36 shall be above 250 Mpa for the thickness equal or belows 200millimeters.For steel plate thickness above 200mm,this value shall be above 220Mpa.The tensile strength of A36 ...

A36 Steel Plate | Midwest Steel & Aluminum

A36 Steel Plate is offered in thicknesses 1/4" through 6". Steel plate is processed by flame cutting or High Def Plasma cutting. Hi Def Plasma is utilized to sizes 1" and under, over 1" is flame cut. A36 Steel plate has a 36,000 min yield strength. Steel Plate. Steel plate A36 is stocked in all pattern sizes up to 96" x 288" and can be ...

ASTM A36 Hot Rolled Steel Plate | A36 Steel Plate | Buy ...

Buy Metal Online – A36 Hot Rolled Steel Plate – Order Large or Small Quantity Online – Cut to Size A36 Steel Plate – No Minimum Order

A36 Steel Plate | Precision Grinding, Inc.

A36 steel general information. The A36 steel specification was first issued in 1960. Today, engineers specify ASTM A36 for more structural steel fabrications than any other type of plate. Consequently, it is the most purchased hot-roll steel plate in the world and …

ASTM A36 Steel Plate - A36 Carbon Steel Plate | Leeco ...

leecosteel› Steel Plate ProductsLeeco Steel distributes ASTM A36 steel plate, which is one of the most widely used carbon structural steels used in the industry. A36 carbon steel plate can be riveted, bolted, or welded in the construction of bridges and buildings, and for general structural purposes. We offer various thicknesses, lengths, and widths to meet your specifications.

0.25" A36 Hot Rolled Plate - Online Metal Store

Hot Rolled Steel Plate A36 (0.25") is made of low carbon steel that is commonly found in most industries as it offers good weldability, machinability, and can be heat treated to harden its surface. Unlike cold rolled steel, Hot Rolled Steel Plate A36 has a rougher surface and …

ASTM A36 & SA36 Steel Plate Supplier - Rolled A36 & SA36 ...

universalsteelamerica› …› ASTM Structural PlatesUniversal Steel stocks A36 / SA36 from 3/16” thick up to 12.5” thick, provided in the as-rolled condition. This is the most commonly used grade of structural carbon steel plate with general applications across all …

A569, ASTM A1011, ASTM A36 Carbon Steel Sheet Stock ...

A569, ASTM A1011, ASTM A36 Carbon steel blanks, flats, bars, plates and sheet stock from Grainger come in a variety of widths, lengths and thicknesses for your industrial applications.

ASTM A36 / A36M - 14 Standard Specification for Carbon ...

A36 / A36M-14 Standard Specification for Carbon Structural Steel shapes~ welded construction~ bolted construction~ riveted construction~ ~ steel plates~ steel bars~ ... A1018/A1018M Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing ... Standard Specification for Carbon Structural Steel ...

Astm A36 Standard Steel Plate Thickness, Astm ... - Alibaba

Alibaba offers 1,285 astm a36 standard steel plate thickness products. About 1% of these are steel pipes. A wide variety of astm a36 standard steel plate thickness options are …

ASTM A36 heavy steel plate width and thickness steel plate ...

BBN steel keep ASTM A36 heavy steel plate,A36 steel all kinds of thickness stock 100000 Ton. ASTM A36 heavy steel plate is one of the most widely used carbon structural steels used in the industry.ASTM A36 heavy steel plate application is widely,ASTM A36 heavy steel plate can be riveted, bolted or welded in the construction of bridges and buildings, and for general structural purposes.

ASTM A36 & SA36 Steel Plate Supplier - Rolled A36 & SA36 ...

universalsteelamerica› …› ASTM Structural PlatesUniversal Steel stocks A36 / SA36 from 3/16” thick up to 12.5” thick, provided in the as-rolled condition. This is the most commonly used grade of structural carbon steel plate with general applications across all …

MetalsDepot® - Buy A36 Steel Plate Online!

Steel Plate, also known as Hot Rolled A36 Steel Plate is a structural quality steel plate used for a large variety of general construction and industrial applications.. Specifications: ASTM A36, AISI A-36 ; Applications: base plates, gussets, liners, road plates, trench covers, etc. Workability: Easy to Weld, Cut, Form and Machine

Grade A36 Steel | McMaster-Carr

Choose from our selection of grade A36 steel, including tight-tolerance low-carbon steel bars, low-carbon steel sheets and bars, and more. In stock and ready to ship. Contact Us Order ... The thickness is held to a ±0.001" (0 ...

Checker Plate ASTM B209, ASTM A36 Thickness 2 - 12 mm

Checker steel plate thickness 10 mm, length 1.35 m, width 0.9 m. Plate steel floor rolled checkered size: length 2500 mm × width 1250 mm × thickness 6 mm. ... A36 (DIN17100 ST37.2) plate and sheet with raised thread, thickness 6 mm and size 2000 mm × 1000 mm. ASTM A36 checker plate. Plate size: 1500 mm × 6000 mm × 8 mm thickness.

A36 Steel Sheets & Plates - aspirinox

ASTM A36 Sheets, Carbon Steel A36 Cold Rolled Plates, ASME SA A36 Shim Sheets, A36 Carbon Steel Slatting Coils, A36 Carbon Steel Hot Rolled Sheets Stockists & Exporter. Aspirinox Alloys Inc is a recognized manufacturer supplier and exporter of A36 Steel Sheets & Plates. The offered range of A36 Steel Sheets is known as low carbon content steel ...

Metric Plate A36 Carbon Steel | Metric Metal

North America's largest supplier of A36 carbon steel metric plates. North America's largest supplier of A36 carbon steel metric plates. ... CARBON PLATE A36. CARBON PLATE A36. Thickness (mm) Clear: Dimensions * Units * Comments . Quantity. Add to cart. Add to Quote. SKU: ...

ASTM A36 Steel Plate - Completely Specifications You ...

ASTM A36 is said to be same as EN S275 steel plate. A36 steel is a very low carbon steel that blends great strength with form ability. It can be safely welded with minimum caution. This structural steel plate can be galvanized to give enhanced corrosion resistance which ensures superior quality. Yield Strength and Tensile Strength

Speedy Metals Information for Hot Rolled Carbon Steel Plate

ASTM A36 A basic oxygen process steel, ASTM A36 has good forming and welding ability, and can be hardened within its carbon limitations. Generally supplied flame cut to size (BTS) or flame cut to print shape (BPP), it can be sheared easily in thin thicknesses, typically ¼" thick and smaller.

A36 steel - Wikipedia

A36 steel has a Poisson's ratio of 0.26, and a shear modulus of 75 GPa (10,900,000 psi). A36 steel in plates, bars, and shapes with a thickness of less than 8 in (203 mm) has a minimum yield strength of 36,000 psi (250 MPa) and ultimate tensile strength of 58,000–80,000 psi (400–550 MPa).Properties·

astm A36 steel plate tolerances

astm A36 steel plate tolerances steel is a building material composed of chemical components such as silicon, sulfur and phosphorus. astm A36 steel plate tolerances can be used F, b, z were expressed as boiling steel, semi-static steel, killed steel.[PDF]

PRODUCT GUIDES - Central Steel and Wire Company: …

Strip mill plate is leveled from coil. This process cannot be applied with heavier thicknesses (see Discrete Plate) Temper Pass A temper mill is a steel sheet and/or steel plate processing line composed of a horizontal pass cold rolling mill stand. Goal is to correct shape differences along the width of the coil through cold forming. The end

ASTM A36 / A36M - 14 Standard Specification for Carbon ...

A36 / A36M-14 Standard Specification for Carbon Structural Steel shapes~ welded construction~ bolted construction~ riveted construction~ ~ steel plates~ steel bars~ ... A1018/A1018M Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing ... Standard Specification for Carbon Structural Steel ...

Common Steel Sheet Thickness

Structural Steel (SS) on the thickness. Each of the steel sheet designations is associated with unique requirements for chemical. ... ASTM A36 Hot Rolled Steel Plate | A36 Steel Plate | Buy . Buy Metal Online – A36 Hot Rolled Steel Plate – Order Large or Small Quantity Online – Cut to Size A36 Steel Plate – No Minimum Order ...

Steel grade

Steel specification

Our advantage

Steel Plate

1).2500mm production line-(Width:1600-2300mm, Thickness:6-30mm,Annual capacity:1,600,000 Tons;

The mainly steel plate we specialized in producing are shipbuilding steel, weathering resistant steel, boiler and pressure vessel steel, pipeline steel and so on. In addition, we can also arrange production according to the following standards - EN10025, EN10028, DIN 17100, ASTM A131, JISG3101, JISG3106...

2).3500mm production line-(Width:2000-3050mm, Thickness:10-80mm, Annual capacity: 2,000,000 Tons;

3).4300mm production line-(Width:1500-4100mm, Thickness:6-300mm, Annual capacity: 1,800,000 Tons;

Steel Pipe

The Seamless pipe production line range is OD 10.3mm--965.2mm, wall thickness 1.0mm--120mm, Annual capacity is 500 thousand tons.

We can do shot blasting and anti-corrosion according to DIN 30670 for diameter 10mm-3500mm,which is the most advanced level in China. To guarantee the quality, we can do Hydraulic test, Ultrasonic Testing, X-Ray test and drop hammer test before each shipment.

LSAW pipe production line range is OD 406mm--2500mm, wall thickness 6mm--50mm, Annual capacity is 150 thousand tons.

ERW pipe production line range is OD 17.1mm--660mm, wall thickness 0.6mm--22mm, Annual capacity is 100 thousand tons.

SSAW pipe production line range is OD 219.1mm--3500mm, wall thickness 3.2mm--25.4mm, Annual capacity is 200 thousand tons.

Stainless Steel

Cold rolled stainless steel plate/coil- (Thickness: 0.3-3.0mm; Width: 1000-2000mm; Length: According to customer's requirement; Surface:2B, 2D, BA, No.3, No.4)

Bebon has long term cooperation with TISCO, LISCO, ZPSS and Bao steel, etc..which are the top biggest and most famous stainless steel factories. Due to the good relationship with them, we have become their first-class agent. We can provide the best quality goods with competitive price.

Steel Plate & Coil Specification

Hot rolled stainless steel coil sheet
Cold rolled stainless steel coil & sheet
Thickness
3.0-12.0mm
Thickness
0.3-3.0 mm
Width
1219mm
Width
1000,1219,1500
Length
coil or as per requirement.
Length
coil or as per requirement.
Surface
No.1 or 1D
Surface
2B
Original
TISCO
Original
TISCO
Standard
GB/T4237-2015 ASTM A240/A240M JIS G4304
Standard
GB/T3280-2007 ASTM A240/A240M JIS G4305 EN10088-2:2005
MOQ for coil
13mt or as per coil actual weight
MOQ for coil
5mt or as per coil actual weight
MOQ for sheet
5 Pcs
MOQ for sheet
5 Pcs

According to the composition is divided into carbon steel and alloy steel, can be further classified according to uses, high strength low alloy steel plate, boilers and pressure vessels steel plate, mold plate, and shipbuilding and offshore platform steel plate, pipeline steel plate, wear-resistant steel plate, military uses steel plate and so on,

Boiler Or Pressure Vessel Steel Plate

It includes carbon steel, carbon manganese steel, micro-alloy steel, low alloy and high strength steel and low temperature steel. The working temperature is generally from -20C to 500C, and the individual can reach 560 degrees centigrade. The Pressure vessel steel plate is a special material related to the national economy and the people's livelihood. It is a short line product of the metallurgical industry.
Pressure Vessel Steel plate have many types, we can provide SA387, SA516, SA537, SA517 and so on, American Standard boiler or pressure vessel steel plate, already export to the United States, Australia, the Middle East, Southeast Asia and many other countries, high quality and low price, can be cut according to customer requirements..

Steel Standard:
ASTM A203 / ASME SA203, ASTM A204 / ASME SA204, ASTM A285 / ASME SA285
ASTM A299 / ASME SA299, ASTM A302 / ASME SA302, ASTM A387 / ASME SA387
ASTM A515 / ASME SA515, ASTM A516 / ASME SA516, ASTM A517 / ASME SA517
ASTM A533 / ASME SA533, ASTM A537 / ASME SA537, ASTM A612 / ASME SA612
ASTM A662 / ASME SA662
EN10028-2, EN10028-3, EN10028-5
DIN 17155

Carbon And Low-Alloy High-Strength Steel Plate

Carbon Steel, main point is that the mass fraction of carbon is less than 2.11% and does not contain the alloy elements and are specially added. Low-alloy high-strength steel is a kind of engineering structural steel developed by adding a small amount of Mn, Si and trace elements such as Nb, V, Ti and Al in the basis of Carbon structural steel.
The so-called low alloy is that the total alloy elements in the steel do not exceed 3%, which are mainly used for manufacturing various engineering structures with high strength, such as bridges, ships, vehicles, high pressure vessels, oil and gas transmission pipelines, large steel structures and so on.
Carbon steel plate and low alloy high strength steel plate, is the most common and widely used steel plate, strong supply capacity, the domestic production of the largest steel plate, we can cut processing according to customer requirements, and also can be processed according to the requirements of the drawings by grinder, our finished products are praised by our many customers, welcome to send us the enquiries and the drawing.

Steel Standard:
ASTM A36, ASTM A283, ASTM A514 / ASME SA514
ASTM A572 / ASME SA572, ASTM A633 / ASME SA633, ASTM A709
EN10025-2, EN10025-3, EN10025-4, EN10025-6 
DIN17100, DIN17102
GB/T700, GB/T1591, GB/T16270

Shipbuilding Or Offshore Structural Steel Plate

Marine steel plate refers to the hot rolled steel plate used to manufacture the hull structure according to the standard requirements of the Classification Society. Shipbuilding or Offshore structural steel plate, first, good toughness is the most critical requirement. In addition, it requires high strength, good corrosion resistance, welding performance, processing performance and surface quality. In order to ensure quality and ensure enough toughness, the chemical composition of Mn/C is above 2.5, and the carbon equivalent is also strictly required, and it is produced by a steel factory approved by the Ship Inspection Department. With the development of marine industry, the steel demand is rising dramatically, in addition to the ordinary ship plate, offshore platform steel plate in recent years is the demanded for a wide range. Our Steel's EN10225 standard steel plate, get the praise of our many customers, including S355G7, S355G8.

Ship Class Steel Plate

Standard: CCS, ABS, LR, GL, BV, DNV, KR, RINA, ETC

Grade :A, B, D, E, AH36, DH36, EH36, AH40, DH40, EH40, FH36, FH40

Thickness : 8mm-500mm 
Width : 1000mm-4000mm 
Length : 1000mm-20000mm


EN10225 Weldable Structural Steels for Fixed Offshore Structures.

Standard: EN10225
Grade :S355G2+N, S355G3+N, S355G5+M, S355G6+M, S355G7+N, S355G8+N, S355G7+M, S355G8+M, S355G9+N, S355G9+M, S355G10+N, S355G10+M
S460G1+QT, S460G1+M, S420G2+QT, S420G2+M,S460G3, S460G4,and so on.

Thickness : 8mm-500mm 
Width : 1000mm-4000mm 
Length : 1000mm-20000mm


API Spec 2H specification for Carbon Manganese Steel Plate for Offshore Structures, API Spec 2H specification covers two grades of intermediate strength steel plates up to 4 in. thick for use in welded construction of offshore structures

Standard: API SPEC 2H
Grade :API Spec 2H Grade 42, Grade 50

Thickness : 8mm-500mm 
Width : 1000mm-4000mm 
Length : 1000mm-20000mm

Wear Resistant Steel Plate

Wear resistant steel plate has high wear resistance and good impact resistance, capable of cutting, bending, welding, welding, can take the plug welding and bolt connecting with other structures are connected, the advantages of time saving, convenient in maintenance process, widely used in metallurgy, coal, cement, electricity, glass, mining, building materials, tiles and other industries, compared with other materials, has a very high price, has been more and more favored by the industry and manufacturers.

Standard: WEAR RESISTANCE STEEL PALTE
Grade :NM360, NM400, NM500, NM550

WNM360, WNM400, WNM450, WNM500

Thickness : 8mm-150mm 
Width : 1000mm-4000mm 
Length : 1000mm-20000mm


If you are interested in our company or products, welcome to visit our company or local offices; you can also get contact with us through online consulting, demand table submission, e-mails and telephones. Our staff shall wholeheartedly provide product information, application knowledge and good service for you.

Inquiry

Please send your processing requirement/ the drawings to sales1@bebonchina.com or leave a message below. Our professional after-sales personnel will response you in 24 hours.