Tel: +86-371-86151827

high strength sae 1010 steel plate

Steel grade:high strength sae 1010 steel plate

Thickness: 2mm-500mm

Certification: ABS, GL, BV, GOST, TS, CCS, CNNC, ISO

Payment Terms: T/T OR LC at sight

steel plate is widely used, involving various mechanical and engineering fields.

Tel: +86-371-86151827

E-mail: [sales1@bebonchina.com]

high strength sae 1010 steel plate Introduction

SAE 1010 steel - steel-grades

High strength after cold forming. Used in railway vehicle, conveyor belt, bolt and nut, etc. Y1Cr18Ni9Se: GB: ... SAE 1010 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.Carbon Steel · Stainless Steel · Tool Steel And Hard Alloy

SAE1010 steel plate - BEBON INTERNATIONAL

Under ASTM standard, we can regard SAE1010 steel plate/sheet as stamping and cold forming steels. SAE1010 is mainly used as stamping and cold forming steels.SAE1010 steel plate/sheet is stamping and cold forming steels,which is according to ASTM-SAE standard,and based on the different thickness,the tensile strength of A621DQ-SAE1010 is 440MPa.The ASTM-SAE A621DQ-SAE1010 is equivalent to ...

ASTM SAE 1010 steel plate - Katalor Industry

ASTM - SAE A 621 CQ - SAE 1010 steel plate/sheet is stamping and cold forming steels,it is suitable for non-structural press work and forming.It's tensile strength is around 420 MPa (there is different min strength point at the different thickness.) A 621 CQ - SAE 1010 yield strength is from 170MPa to 320 MPa. (different min strength point at the different thickness.)

Low Alloy High Strength Sae 1010 1020 1045 Steel Plate

AISI 1010 carbon steel is a plain carbon steel with 0.10% carbon content. This steel has relatively low strength but it can be quenched and tempered to increase strength. The following datasheet provides more details about AISI 1010 carbon steel. Steel Plate Sae 1010/1020/1045, Steel Plate Sae 1010/1020 ... Contact Details sae 1010/1020/1045 1.

SAE 1010 1020 1045 steel plate - hopkinsplasticsurgery

Practical Maintenance » Blog Archive » Classification of … There are many low-alloy steels that are not classified under the above mentioned AISI/SAE system. Thus, the situation with low-alloy steels becomes much more complicated. For example, HY-80, a steel widely used for high-strength plate …

SAE A 621 CQ - SAE 1010 steel plate - BEBON steel

ASTM - SAE A 621 CQ - SAE 1010 steel plate/sheet for stamping and cold forming steels A 621 CQ - SAE 1010 steel plate/sheet, under ASTM - SAE standard, we can regard A 621 CQ - SAE 1010 steel plate/sheet as stamping and cold forming steels.[PDF]

Datasheet for Steel Grades Carbon Steel SAE 1010

This page is mainly introduced the SAE 1010 Datasheet, including chemical information,mechanical properties, physical properties, mechanical properties, heat treatment, and Micro structure, etc. It also contains the use of SAE 1010,such as it is commonly used in bars, sheet,plates, steel coils, steel pipes,forged and other materials application.

AISI 1010 Carbon Steel (UNS G10100) - AZoM

AISI 1010 carbon steel is a plain carbon steel with 0.10% carbon content. This steel has relatively low strength but it can be quenched and tempered to increase strength. The following datasheet provides more details about AISI 1010 carbon steel. Chemical Composition. The following table shows the chemical composition of the AISI 1010 carbon steel.[PDF]

Section F - emjmetals

SHeetS—PLAteS High strength low alloy (HSLA) steels are essentially low carbon steels to which ... SAE J410 Grade 950X (Sheets, Plates) Resistance to Atmospheric corrosion two times that of carbon Steels color Marking: Red and White ... HiGH StRenGtH LoW ALLoY SteeL (Continued) HiGH HiGH StRenGtH StRenGtH SHeetS PLAteS Width est . Wt .

SAE 1010 steel - steel-grades

High strength after cold forming. Used in railway vehicle, conveyor belt, bolt and nut, etc. Y1Cr18Ni9Se: GB: ... SAE 1010 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.

SAE Steels, AISI Specifications,CSA, High Strength Steels

High Yield (HY) HIGH STRENGTH STEELS. AISI Specifications - (CSA SAE) STEELS CHARTS . ALL WELDS SHOULD FIRST BE PRE-QUALIFIED BEFORE ... the governing specifications or codes, the plate condition, plate thickness, the weld consumables the weld procedures, the weld size and amount of welds required. ... AISI SAE HIGH STRENGTH SHEET STEEL ...

AISI 1010, AISI 1010 Steel Plate, AISI 1010 Structural ...

Sell AISI 1010, AISI 1010 Steel Plate, AISI 1010 Structural Steel1. Steel Grade: AISI 1010, AISI 1010 Steel Plate, AISI 1010 Structural Steel2. Supply steel Size: Thickness: 3mm to 150mm Width: 1000mm to …

Aisi 1010 Hot Rolled Steel Plate - gmatindia.in

A wide variety of aisi 1010 1020 hot rolled steel plate options are available to you, such as aisi, astm, and jis. You can also choose from steel plate, steel coil, and plate. As well as from hot rolled, cold rolled. And whether aisi 1010 1020 hot rolled steel plate is high-strength steel plate, or wear resistant steel…

AISI 1010,1010 Carbon Steel,SAE ... - s690q-heavy-plate

AISI 1010,1010 Carbon Steel,SAE 1010, 1010 Stock,1010 Steel Plate Category: Low High Strength and Super Thick Steel Plate Model: Gangsteel Carbon Plate Factory are specialized in producing and exporting 1010 AISI-SAE Standard Carbon Steel plates ,Low alloy and high strength steel plate, heavy plate and wide, heavy plate, Which is a large steel plate supplier mill at Gangsteel Group.

sae1010 yield strength - Mild Cold Rolled steel plate

ASTM SAE 1010 steel plate - Katalor Industry. SAE 1010 steel plate can be offered by Katalor industry,Katalor industry is professional ASTM SAE 1010 steel plate suppliers and manufacturer ,if you need ASTM SAE 1010 steel plate price ,please contact us. A 621 CQ - SAE 1010 yield strength is from 170MPa to 320 MPa.

Low Alloy High Strength Sae1008 Steel Plate

Give You Our Best Carbon Steel Plate TStE460 low alloy ... Carbon and Low-alloy High-strength Steel Plate. Carbon and Low-alloy High-strength Steel Plate is Widely Used In Construction of Bridges, Riveted, Bolted, And Other Structural Elements Included Drilling Machine, Power Shovel, Electricity Drive Wheel Counter- Mine Trolley, Mineral Product Automobile, Excavator, Car Loader.

Steel Plates, Metal Plates, Cincinnati, Ohio - tmtco

Quenched and tempered constructional alloy steel with unique combination of high yield strength, weldabilty, and good toughness. Used in bridges, towers, earth moving equipment, booms, bucket parts for power shovels, cranes, fork lift parts, mining equipment, and tanks. SAE or AISI 4140: Economical alloy steel which develops high strength and ...

Steel Plate Grades - Continental Steel & Tube Company

ASTM A572 STEEL (GRADE 50) INX-EXTEN is available with. 50,000 psi min strength level. It is moderately priced and offers high strength in combination with good formability and weldability. Atmospheric corrosion resistance is about equal to plain carbon steel. Conform to SAE J41 0 and Grade 950X. STEEL PLATE COILS

Tensile Strength 1010 Steel, Tensile Strength 1010 Steel ...

Alibaba offers 96 tensile strength 1010 steel products. About 6% of these are steel sheets, 4% are steel wire, and 3% are steel pipes. A wide variety of tensile strength 1010 steel options are available to you, such as drawn wire, galvanized.

SAE 1010, SAE 1015, SAE 1018, SAE 1020 Steel Plate-SA240 ...

SAE 1010, SAE 1015, SAE 1018, SAE 1020 Steel Plate . Unitedsteel Carbon Plate Factory are specialized in producing and exporting SAE 1010, SAE 1015, SAE 1018, SAE 1020 Standard Carbon Steel plates ,Low alloy and high strength steel plate, heavy plate and wide, heavy plate, Which is a large steel plate supplier mill at Unitedsteel Group.

SAE A 621 CQ - SAE 1010 steel plate - BEBON steel

ASTM - SAE A 621 CQ - SAE 1010 steel plate/sheet for stamping and cold forming steels A 621 CQ - SAE 1010 steel plate/sheet, under ASTM - SAE standard, we can regard A 621 CQ - SAE 1010 steel plate/sheet as stamping and cold forming steels.

C1020 Steel Plate- AISI 1020 Steel Plate | Leeco Steel, LLC

leecosteel› Steel Plate ProductsC1020 Steel Plate. Please call Leeco Steel at 1-888-828-7897 to be connected to a member of our sales team who can share more information about C1020 steel plate. ... Mild and high strength low-alloy (HSLA) steel make up the skeleton of our infrastructure and play important roles in construction industries. This article will explore mild and ...

SAE steel grades - Wikipedia

The SAE steel grades system is a standard alloy numbering systems for steel grades maintained by SAE International. In the 1930s and 1940s the American Iron and Steel Institute (AISI) and SAE were both involved in efforts to standardize such a numbering system for steels. These efforts were similar and overlapped significantly.Carbon steel·

Steel grade

Steel specification

Our advantage

Steel Plate

1).2500mm production line-(Width:1600-2300mm, Thickness:6-30mm,Annual capacity:1,600,000 Tons;

The mainly steel plate we specialized in producing are shipbuilding steel, weathering resistant steel, boiler and pressure vessel steel, pipeline steel and so on. In addition, we can also arrange production according to the following standards - EN10025, EN10028, DIN 17100, ASTM A131, JISG3101, JISG3106...

2).3500mm production line-(Width:2000-3050mm, Thickness:10-80mm, Annual capacity: 2,000,000 Tons;

3).4300mm production line-(Width:1500-4100mm, Thickness:6-300mm, Annual capacity: 1,800,000 Tons;

Steel Pipe

The Seamless pipe production line range is OD 10.3mm--965.2mm, wall thickness 1.0mm--120mm, Annual capacity is 500 thousand tons.

We can do shot blasting and anti-corrosion according to DIN 30670 for diameter 10mm-3500mm,which is the most advanced level in China. To guarantee the quality, we can do Hydraulic test, Ultrasonic Testing, X-Ray test and drop hammer test before each shipment.

LSAW pipe production line range is OD 406mm--2500mm, wall thickness 6mm--50mm, Annual capacity is 150 thousand tons.

ERW pipe production line range is OD 17.1mm--660mm, wall thickness 0.6mm--22mm, Annual capacity is 100 thousand tons.

SSAW pipe production line range is OD 219.1mm--3500mm, wall thickness 3.2mm--25.4mm, Annual capacity is 200 thousand tons.

Stainless Steel

Cold rolled stainless steel plate/coil- (Thickness: 0.3-3.0mm; Width: 1000-2000mm; Length: According to customer's requirement; Surface:2B, 2D, BA, No.3, No.4)

Bebon has long term cooperation with TISCO, LISCO, ZPSS and Bao steel, etc..which are the top biggest and most famous stainless steel factories. Due to the good relationship with them, we have become their first-class agent. We can provide the best quality goods with competitive price.

Steel Plate & Coil Specification

Hot rolled stainless steel coil sheet
Cold rolled stainless steel coil & sheet
Thickness
3.0-12.0mm
Thickness
0.3-3.0 mm
Width
1219mm
Width
1000,1219,1500
Length
coil or as per requirement.
Length
coil or as per requirement.
Surface
No.1 or 1D
Surface
2B
Original
TISCO
Original
TISCO
Standard
GB/T4237-2015 ASTM A240/A240M JIS G4304
Standard
GB/T3280-2007 ASTM A240/A240M JIS G4305 EN10088-2:2005
MOQ for coil
13mt or as per coil actual weight
MOQ for coil
5mt or as per coil actual weight
MOQ for sheet
5 Pcs
MOQ for sheet
5 Pcs

According to the composition is divided into carbon steel and alloy steel, can be further classified according to uses, high strength low alloy steel plate, boilers and pressure vessels steel plate, mold plate, and shipbuilding and offshore platform steel plate, pipeline steel plate, wear-resistant steel plate, military uses steel plate and so on,

Boiler Or Pressure Vessel Steel Plate

It includes carbon steel, carbon manganese steel, micro-alloy steel, low alloy and high strength steel and low temperature steel. The working temperature is generally from -20C to 500C, and the individual can reach 560 degrees centigrade. The Pressure vessel steel plate is a special material related to the national economy and the people's livelihood. It is a short line product of the metallurgical industry.
Pressure Vessel Steel plate have many types, we can provide SA387, SA516, SA537, SA517 and so on, American Standard boiler or pressure vessel steel plate, already export to the United States, Australia, the Middle East, Southeast Asia and many other countries, high quality and low price, can be cut according to customer requirements..

Steel Standard:
ASTM A203 / ASME SA203, ASTM A204 / ASME SA204, ASTM A285 / ASME SA285
ASTM A299 / ASME SA299, ASTM A302 / ASME SA302, ASTM A387 / ASME SA387
ASTM A515 / ASME SA515, ASTM A516 / ASME SA516, ASTM A517 / ASME SA517
ASTM A533 / ASME SA533, ASTM A537 / ASME SA537, ASTM A612 / ASME SA612
ASTM A662 / ASME SA662
EN10028-2, EN10028-3, EN10028-5
DIN 17155

Carbon And Low-Alloy High-Strength Steel Plate

Carbon Steel, main point is that the mass fraction of carbon is less than 2.11% and does not contain the alloy elements and are specially added. Low-alloy high-strength steel is a kind of engineering structural steel developed by adding a small amount of Mn, Si and trace elements such as Nb, V, Ti and Al in the basis of Carbon structural steel.
The so-called low alloy is that the total alloy elements in the steel do not exceed 3%, which are mainly used for manufacturing various engineering structures with high strength, such as bridges, ships, vehicles, high pressure vessels, oil and gas transmission pipelines, large steel structures and so on.
Carbon steel plate and low alloy high strength steel plate, is the most common and widely used steel plate, strong supply capacity, the domestic production of the largest steel plate, we can cut processing according to customer requirements, and also can be processed according to the requirements of the drawings by grinder, our finished products are praised by our many customers, welcome to send us the enquiries and the drawing.

Steel Standard:
ASTM A36, ASTM A283, ASTM A514 / ASME SA514
ASTM A572 / ASME SA572, ASTM A633 / ASME SA633, ASTM A709
EN10025-2, EN10025-3, EN10025-4, EN10025-6 
DIN17100, DIN17102
GB/T700, GB/T1591, GB/T16270

Shipbuilding Or Offshore Structural Steel Plate

Marine steel plate refers to the hot rolled steel plate used to manufacture the hull structure according to the standard requirements of the Classification Society. Shipbuilding or Offshore structural steel plate, first, good toughness is the most critical requirement. In addition, it requires high strength, good corrosion resistance, welding performance, processing performance and surface quality. In order to ensure quality and ensure enough toughness, the chemical composition of Mn/C is above 2.5, and the carbon equivalent is also strictly required, and it is produced by a steel factory approved by the Ship Inspection Department. With the development of marine industry, the steel demand is rising dramatically, in addition to the ordinary ship plate, offshore platform steel plate in recent years is the demanded for a wide range. Our Steel's EN10225 standard steel plate, get the praise of our many customers, including S355G7, S355G8.

Ship Class Steel Plate

Standard: CCS, ABS, LR, GL, BV, DNV, KR, RINA, ETC

Grade :A, B, D, E, AH36, DH36, EH36, AH40, DH40, EH40, FH36, FH40

Thickness : 8mm-500mm 
Width : 1000mm-4000mm 
Length : 1000mm-20000mm


EN10225 Weldable Structural Steels for Fixed Offshore Structures.

Standard: EN10225
Grade :S355G2+N, S355G3+N, S355G5+M, S355G6+M, S355G7+N, S355G8+N, S355G7+M, S355G8+M, S355G9+N, S355G9+M, S355G10+N, S355G10+M
S460G1+QT, S460G1+M, S420G2+QT, S420G2+M,S460G3, S460G4,and so on.

Thickness : 8mm-500mm 
Width : 1000mm-4000mm 
Length : 1000mm-20000mm


API Spec 2H specification for Carbon Manganese Steel Plate for Offshore Structures, API Spec 2H specification covers two grades of intermediate strength steel plates up to 4 in. thick for use in welded construction of offshore structures

Standard: API SPEC 2H
Grade :API Spec 2H Grade 42, Grade 50

Thickness : 8mm-500mm 
Width : 1000mm-4000mm 
Length : 1000mm-20000mm

Wear Resistant Steel Plate

Wear resistant steel plate has high wear resistance and good impact resistance, capable of cutting, bending, welding, welding, can take the plug welding and bolt connecting with other structures are connected, the advantages of time saving, convenient in maintenance process, widely used in metallurgy, coal, cement, electricity, glass, mining, building materials, tiles and other industries, compared with other materials, has a very high price, has been more and more favored by the industry and manufacturers.

Standard: WEAR RESISTANCE STEEL PALTE
Grade :NM360, NM400, NM500, NM550

WNM360, WNM400, WNM450, WNM500

Thickness : 8mm-150mm 
Width : 1000mm-4000mm 
Length : 1000mm-20000mm


If you are interested in our company or products, welcome to visit our company or local offices; you can also get contact with us through online consulting, demand table submission, e-mails and telephones. Our staff shall wholeheartedly provide product information, application knowledge and good service for you.

Inquiry

Please send your processing requirement/ the drawings to sales1@bebonchina.com or leave a message below. Our professional after-sales personnel will response you in 24 hours.